Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: H tranny rebuild


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Scott Swanson on July 15, 2005 at 10:13:19 from (70.59.122.201):

In Reply to: H tranny rebuild posted by Hpoor on July 14, 2005 at 19:37:58:

It is not hard, just time consuming. Do it in steps and protect yourself from bodily harm. Farmalls can be dangerous to work on. They are heavy and cumbersome. Get a repair manual and follow it. Replace EVERY seal you touch and remove and replace the pilot bearing regardless of how it looks or acts. These old tractors were neglected beyond belief. They we used and used and used and still ran.

I am totally amazed at the design. My Dad's Farmall is a 1942. We ran it flat out on a Buzz Saw setup for 6 years. That was 15 years ago and I am still using it to put in the boat, pull stumps, pull down trees, pull the leaf wagon and generally pull me around for no reason at all.

If you pull the tranny cover......fix it all or make darn sure everything in there is working right. Put the entire rear of the tractor on jackstands and round up a ton of rags. You may even want to flush out the old tranny oil with diesel full. The black stuff in there now is murder on clothing and will stain your hands for a week.

Buy used gears when you can. New gears are outrageously priced. Replace worn gears and the ones they run against. Replace all oil seals everywhere. Be careful not to break stuff. Replacements can be expensive. Remove and regrease the shifter forks, springs, and detent balls in the cover.

Only disasemble what needs to be replaced. Do not mess around with stuff that is working in there. You do not need to split the tractor.

Be careful with the shims that end up in your hand. Put them back in the same place they came from. They are fragile.

First of all...try to identify the problem and then go for it.

Have fun!


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Experimental Tractors Article - by Danny Bowes (Dsl). Tractor technology appears to have nearly hit it's pinnacle of development. If you agreed with the subtitle, you are rather mistaken. Quite, actually. As a matter of fact, some of the technology experimented with over 40 years ago makes today's tractor technology seem absolutely stale by comparison. Experimentation, from the most complex assembly to the most simple and mundane component, is as an integral a part of any farm tractor's development ... [Read Article]

Latest Ad: 1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy