|
Farmall & IHC Tractors Discussion Board |
Farmall 130 carburator acting up
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hugh MacKay on February 01, 2007 at 05:57:57 from (209.226.106.128):
Yesterday morning I went out to plow snow, about -10C or 15F. 130 fired right up, initially I was plowing 1/2 throttle in 1st gear. After about 15 min. tractor started to sputter and at first was able to keep it running with choke. After about 2 min. and with choke out all the way it died. My first reaction was ice, thus I added some methyl hydrate to fuel, loosened fuel line at carb to insure fuel was coming and to speed up mh getting to carb. 10 min. plowing again 1/2 throttle and same thing. Next I removed elbo and screen to carb. It was not plugged, however I did blow air through it. 10 min. later and same thing again. This time I changed oil in breather, and put a wrench on carb mounting bolts. I got about a 1/4 turn on those. By now my yard and short little pushes were all cleaned up, just my 400' driveway left. Out of the shed and full throttle in 2nd gear pushing snow often to top of blade and lugging the tractor quite hard. I decided while things were working well to roll the snow well back on fields. This went on for about an hour, now i have a trail abot 30' wide that will allow me drifting space should the 130 not want to work well next time. Sure enough I got back to shed idled it down, while idling it stopped. it stopped 3 more times idling while I was backing it in the shed. All this morning action caused 90 min. plowing to take 3 hours. By then this old carcas was cold enough I decided fixing could wait for warmer time. Could a leak in the gasket between carb and manifold be causing this, or do I need to delve deeper into carb. I can tell you this carb ocasionally leaks while tractor is parked, thus I shut the gas off every night. It has been that way since the last carb kit close to 6 years ago. I'm just trying to decide whether I go for a gasket this am, or a complete carb kit. Any advice would be appreciated.
Replies:
Home
| Forums
Today's Featured Article -
Harvestin Corn in Southern Wisconsin: The Early Years - by Pat Browning. In this area of Wisconsin, most crops are raised to support livestock production or dairy herds in various forms. Corn products were harvested for grain, and for ensilage (we always just called it 'silage'). Silo Filling Time On dairy farms back in the 30's and into the first half of the 40's, making of corn silage was done with horses pulling a corn binder producing tied bundles of fresh, sweet-smelling corn plants, nice green leaves with ear; the
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
