Hey retom, I just went through what you did with the oil base / latex transition. My floor is in my commercial kitchen. About 7 years ago I used oil based Porch and Floor enamal pain for my unpainted concrete. It wasn't super smooth and I used muratic acid to open it up better. Then I thined the paint 1:1 with thinner and applied two coats. It absorbed in pretty good. Then the following year I just painted it with straight oil base. Two years later it looked bad - scratched and worn off in the high traffic area. Gave it a couple more coats. Looked great for a while, then started to scratch and wear again. I should have thinned it again to let it absorb into the concrete - but there were crackes and chips in the concrete that were very obvious with the thin coat. Full paint cover them ok.
Getting frusterated - I didn't want to paint every year, or use the two part epoxy. I had a half can of regular latex floor paint from another project. So last September I cleaned the worst area and put one coat of the latex down over it. Now the two colours didn't match, but the latex stuck great. Infact there was no wear or scuffing compared to the oil beside it.
Now about a month ago I decided we better get it all looking good - kitchen inspections comming up... We took a lot of tine on the prep. Over the course of a week we sanded it by hand - just to ruff off the glase three times. We didn't want to take it all off, but I wanted to make sure the new paint would bond well.We then washed it several times...and swepted and swiffered and anything else to get the dust off and made sure it was dry.
I then used a latex floor paint called Drylok - made by UGL. I was aprehensive, but it went on very well. We gave it two coats used and only about 1 3/4 cans. They were about $35 each. The room is 32' X 20'. I am very happy so far. It is not as slick as the oil paint was. It cleans up and washes well. Only time will tell how it holds up. But to answer your question, yes you can paint latex over oil. Just prep, prep and more prep. Good luck, Grant
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Farmall M - by Staff. H so that mountable implements were interchaneable. The Farmall M was most popular with large-acreage row-crop farmers. It was powered by either a high-compression gas engine or a distillate version with lower compression. Options included the Lift-All hydraulic system, a belt pulley, PTO, rubber tires, starter, lights and a swinging drawbar. It could be ordered in the high-crop, wide-front or tricycle configurations. The high-crop version was called a Model MV.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.