Tractor Talk Discussion Board |
Re: IH Utility hydralic problems
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by K.B. on December 06, 2003 at 10:31:49 from (209.163.43.90):
In Reply to: IH Utility hydralic problems posted by Maury Baggett on December 06, 2003 at 05:53:21:
With that system, nine times out of ten the problem is in what they call the Saftey/Regulator valve. Like your 240, most IH tractors in the late '50's used a positve displacement pump and closed-center control valves. This means that the pump produces a constant flow of oil, and since the valves are closed-center, oil cannot flow through them when they are in neutral. To solve this problem, the Saftey/Regulator valve dumps the flow from the pump back to the reservior when the control valves are in neutral. If it sticks open, you don't get any oil to the control valves. You need to rebuild the Saftey/Regulator valve, which is very easy to do. This valve is located under the gas tank on my Farmall 240 Row-Crop. It has a square cover held on by four bolts. Remove the valve from the tractor. Remove two of the bolts that hold on the cover, and install longer bolts, because there is a heavy spring pushing against the cover. Remove the other two bolts, then carefully remove the long bolts you just installed. After you get the cover off, you'll see what looks like a small plug that you can remove with a flat screwdriver. Remove it and you will find that it is a screen. This is called the orfice screen. Get a new one from Case-IH. Replace the o-ring on the regulator valve piston, get a new cover gasket, replace any other o-rings that were disturbed while removing the valve, change hyd. fluid and filter, and you should be ready to go. I would highly reccomend that you get a Parts Manual, because it shows a very detailed exploded view of this valve. An I&T Service Manual might also show this valve.
Follow Ups:
Home
| Forums
Today's Featured Article -
A Belt Pulley? Really Doing Something? - by Chris Pratt. Belt Pulleys! Most of us conjure up a picture of a massive thresher with a wide belt lazily arching to a tractor 35 feet away throwing a cloud of dust, straw and grain, and while nostalgic, not too practical a method of using our tractors. While this may have been the bread and butter of the belt work in the past (since this is what made the money on many farms), the smaller tasks may have been and still can be its real claim to fame. The thresher would bring in the harvest (and income) once a y
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|