Tractor Talk Discussion Board |
Re: OT: Tracing an electrical line
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by John T on October 03, 2005 at 13:06:27 from (66.244.90.98):
In Reply to: Re: OT: Tracing an electrical line posted by dr.sportster on October 03, 2005 at 08:48:25:
dr. Thanks for the good feedback to which I agree. They make GFI "Receptacles" which would protect any loads or lines connected to and/or wired "downstream" of the unit and they also make GFI "Circuit Breakers" which would protect the feeder PLUS any downstream loads. As I understand them there's a torroidal coil through which BOTH the Line and Neutral pass. If the curents the same in BOTH they cancel each other out and no voltage is induced in the coil which can trigger the relay to open. However, if theres an imbalance cuz some of the current flowing to the load from the Line IS NOT ALL BEING RETURNED VIA THE NEUTRAL that means some portion of it it may be leaking off to ground or the equipment user etc. OUCH !!!!!!!!!!! Therefore I agree with your statements and appreciate someone actually reads these posts n thinks about them plus takes the time n cares enough to reply. If the posters feeder wires (to that GFI receptacle) had a fault it may or may not be sufficient to clear his protective device and wouldnt necessarily cause his GFI "Receptacle" to trip out as it wouldnt see the unbalanced flow upstream of it HOWEVER if he had a GFI "Circuit Breaker" feeding n protecting that feeder wire, it would. I never consider a GFI "Receptacle" as an overcurrent protrctive safety device, only as protection if the line current flowing out of it isnt balanced by the returned Neutral current. The GFO "Circuit Breaker" however serevs as BOTH overcurrrent protection PLUS GFI. I love this Sparky chit chat even if we bore others lol Thanks again, John T retired engineer
Follow Ups:
Home
| Forums
Today's Featured Article -
Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|