|
Tractor Talk Discussion Board |
O.T. - 2 Piece Truck Wheels/Split Rims
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Billy NY on December 12, 2005 at 06:56:48 from (64.12.117.7):
I was wondering how everyone who has an older single axle truck handles these, say when it's time to get new tires, will the tire guys still do the work or are these a problem ? I am well aware of how dangerous these are, I do have the original shop manual for this truck, it has a detailed section on the wheels, but I certianly won't fool with them. I have one tire that is flat on the rear, was like that before I made the trip home ( read below ) they just inflated it, and it held air long enough, but I'm also wondering that if just inflating it is dangerous too, or is it just when assembling the 2 piece/split rim after a tire change ? I can recall what happened a about 15 years ago when driving a tri-axle R model Mack, with 29 ton on, blew a front tire on the right side, looked like a grenade went off under the fender, the fender was blown apart, the post mirror on the fender blew off, the battery box cover blew off, and I never found the steel ring that goes on the wheel, it blew off into the woods, have a lot of respect for 110 P.S.I. truck tires after that, not to mention the old split rims Not sure if anyone recalls, but about 1 1/2 months ago I posted a question about crossing the Canadian border by Niagara Falls, Queenston/Lewiston crossing and it was reccommended to not go back the same way after picking up a 1964 F-600 grain truck. I made the trip Nov. 3rd - 4th, 600 miles out and 800 miles back, 34 hours straight, that old F-600 went down the road straight as an arrow, did not burn any oil, the whole thing went smoothly, used 98 gallons of gasoline, only issue is how low it was geared, 3000 r.p.m.'s in 4th with the button up gets you 62 M.P.H. sometimes 65 M.P.H. and it sounds like you are hammering the 292 Y-block engine, not a good highway truck unless I could change the rear or something I suppose, was an experience though, driving a 41 year old truck that far.
Replies:
Home
| Forums
Today's Featured Article -
When Push Comes to Shove - by Dave Patterson. When I was a “kid” (still am to a deree) about two I guess, my parents couldn’t find me one day. They were horrified (we lived by the railroad), my mother thought the worst: "He’s been run over by a train, he’s gone forever!" Where did they find me? Perched up on the seat of the tractor. I’d probably plowed about 3000 acres (in my head anyway) by the time they found me. This is where my love for tractors started and has only gotten worse in my tender 50 yrs on this “green planet”. I’m par
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
