Tractor Talk Discussion Board |
Re: self energizing regulator.
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Bob on April 21, 2006 at 16:33:39 from (64.21.249.40):
In Reply to: self energizing regulator. posted by bng9_2000 on April 21, 2006 at 15:50:33:
All you need is a standard 10SI alternator, available quite reasonably as a rebuilt, or for as little as $5.00 "recycled". Then, jumper the #2 "voltage sense" terminal over to the large output stud. 
Then, run a wire from the switched side of the ignition switch to a 1N5008 (or equivalent) diode, and then from the diode to the alternator's #1 "switched excite" terminal. Run a wire, AT LEAST 10ga. from the alternator's large output stud to the ammeter, or battery side of the starter switch or starter solenoid. This will likely be CHEAPER than going with the goofy one-wire system, will use a standard off-the-shelf Delco 10SI alternator, with no need to tear into it ro make internal "mods". This setup will begin to charge at lower RPM's than the "one-wire" units, and is less likely to put a parasitic drain on the battery that will "kill" it during periods when the machine sits unused. If the machine does not have an ignition switch to supply 12-Volts while the machine is running, you can use an oil pressure switch to send power to the diode only while the engine is running, and has oil pressure. If you do not wish to use a diode, you can use an "idiot lamp" with a #194 lamp in it's place, or use a "side marker lamp" with a #194 lamp, mounted out of sight. BobM, over on the Farmall Board, has graciously posted a series of diagrams of 12-Volt IH tractor conversions, which can, in general, be used on about ANY old machine. He even has one or two with an oil pressure switch in the circuit. His diagrams use the "idiot lights" instead of a diode, but, remember, the diode or the # 194 lamp are direct substitutes for each other. Use which ever appeals to you!
Replies:
Home
| Forums
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|