Tractor Talk Discussion Board |
Re: Castrol Tection 15W-40 oil in a JD 2 cylinder
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by jdemaris on April 14, 2007 at 14:07:27 from (66.218.17.135):
In Reply to: Re: Castrol Tection 15W-40 oil in a JD 2 cylinder posted by Jon Hagen on April 14, 2007 at 11:40:55:
I will assume that you do NOT automatically assume that someone holding the status of shop foreman is an authority on the subject. If you do - we have a problem since I was a Deere Ag. and Ind. shop-foreman for 12 years. So, how does one choose which shop foreman to believe? I say don't believe any of them and do your own research. I don't assume that someone who is an engineer is automatically an authority either. I learned that a long time ago - especially with some Deere engineers I worked with. I'm picking on Deere - only because I've never worked along side any other sort of engineer. But, my father-in-law is a retired Ford engineer and he's filled me in a little about how things work in his type of world. I use spec. charts from oil companies for my own peace-of-mind. And - judging from the oils and their specs - that I use - I disagree with much of what you stated. But - you are free to use what you wish - and believe what you want - just as I am. Most synthetic oils have much more stabil bases in regard to viscosity and do not use the same polymers and petro-based oils. As I said previously - when I'm in doubt - I don't like taking chances and prefer to use something proven by time - not by computerized projections (that are sometimes used). In regard to the new oils being fine with Detroit 2-strokes? I still use the old standy - Rotella T 15W-40 in much of my stuff - but not my Detroits. I got two machines with 3-53s and one with a 3-71. The current data sheet for Rotella T 15W-40 reads (and note the Detroit comments) : Shell Rotella T 15W-40 - 100 degrees C - 15.7 viscosity, 40 degrees C =- 118 vis. Note: Detroit Diesel Series 53, 71, and 92 engines operating in ambient temperatures below 0°F - otherwise use straight 40W.
Replies:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|