Posted by super99 on November 04, 2007 at 17:04:18 from (75.107.167.209):
In Reply to: Re: Got The Bin Up posted by paul on November 04, 2007 at 08:05:21:
I borrowed the jacks, not much to them if you have some pipe laying around, biggest expense would be winches and cable. I had 5 on a 18' bin, we usually try to go 1 on each seam for bigger bins. The stiffeners will be whatever size I can find at the scrap yard, was told they had some 2" angle in long pieces. I'm going to go look after work tomorrow. I have a fan set in the door blowing out right now, plan to leave it on for a week, probably take me that long to get angle iron and drill and put on and put in the door. I'm going to try to get set up to move a little air in there somehow. The shed is 50X80, put it up myself. Has good and bad points. Can't drive a nail in wall to hang anything or put up shelves. Moisture collects on arches and when it warms up, it rains inside. Would like to have one end closed off to have a shop area to heat and work in, but haven't found a cheap way to insulate yet. Spray on is kind of pricey. I like the straight sidewalls, can pull 750 MF with 4 row corn head up next to wall, leave enough room to walk between wall and head and still have roof clearance. If I had to do it over again, I'd probably have a pole barn, BUT the neighbor up the road 1/4 mile has had the end tore out of his pole barn 2 times in the last 6 or 7 years and I haven't had any trouble with that yet. I think you have more options to add onto if you want to at a later date with a pole barn. All I can do is go longer on 1 end. Took 4 people 2 weeks to put up 40 arches, and I was beat when we got done, I did end walls by myself after work and weekends and it took a month to get them done. Go somewhere and look long and hard at one before buying, talk to owner and ask questions. It would have to be at least 1/2 price of a pole barn before I would tackle one again. Not sure if it is possible to get enough ventilation inside with out leaving doors open. Chris
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
