This maybe a bit of review but do you have your draft control lever in D? L is load and the hitch will react to the load placed on it. LD is a mixture of load and depth and the hitch will be less resopnsive to load and more responsive to depth. D is depth and the hitch will no respond to varying loads. Loads in this case do not maen the amount of weight on the three point that you are trying to pick up but rather the amount of draft effort (pulling amount) that the bottom three point arms have on them. An example would be pulling a semi-mount plow which is only hooked to the bottom two arms. As the load increases, (draft) the sensing mechanism transmits the signal to raise the three point slightly.
The 2nd photo shows the position of the feedback roller if you are in D for depth control. This point is basically in line with the cam on the rockshaft and if the dash lever is the command input, the hitch reacts, and the cam (via linkage) cancels. The hitch holds that position.
The roller will stick out much further if you have selected L or load position. The cam has very little effect on positioning the three point when in this position. Varying draft loads, since the roller is now further down on the load sensing arm, do most of the control. Without load, the hitch will raise to the top in the last bit of lever movement and will drop to the bottom at the first bit of moving the lever to lower.
Photo 3 shows the feed back linkage. The right side is a simple differential (similar to a car rear end). The dash lever is hooked to the outside bevel gear, the feedback roller is hooked to the middle gear (spider, meshed to both bevel gears). And the LH bevel gear is hooked to the cam shaft to push the raise/lower balls off their seats. Command input rotates the RH bevel and thru the spider, rotates the LH bevel. This rotates the cam pushing open the correct ball to raise or lower. (Depends which way you moved the lever if you wnated to raise or lower) If in depth, the cam pushes on the roller which moves the spider. Since the RH bevel is held in position by the dash lever, the LH bevel reacts, the cam moves and the ball is returned to it's seat. The hitch stops at it's new position.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
