Posted by john in La on February 01, 2010 at 12:37:03 from (68.222.11.142):
I have a stand alone 5500w generator (6000 surge) I got at home depot or similar place. It broke and the repair guy said it would cost almost as much to repair as buying another so I am in the market for a new generator.
Since I was pushing the limit of the generator I would like to move up to 10,000 watts or even 15,000 if I can talk myself into it.
I only use the generator as a backup if the power goes off and then only if it is off for hrs on end (hurricane) so spending mega bucks on one is not cost efficient. And this is the real problem I have with spending $1000 or more on a generator. On the other hand when the power is off for 1 or 2 weeks a generator is sure nice thing to have.
1) I was looking at the 7200w generator head Harbor Freight has for $300 and trying to figure a way to run it. From the tractor crankshaft; and I even have a 22hp gas motor but it is a bottom shaft so I do not think that will work. If I could figure a way to run this item I would most likely buy it. generator head
2) So I started looking around for a PTO generator. I found several. One 15kw at harbor freight for $1200 w/shipping but I may be able to get this one at the local store 15kw And another 13kw at Northern Tools for $1500 w/shipping. 13kw
Between the two I like the harbor freight item since it would be a easy hookup; especially if I can get it for $1100 at my local store.
3) Then I started reading about generators and I found that a 4 pole 1800 rpm unit with brushes would last a lot longer and MIGHT not be some china junk. I found this 15kw unit for $900. Most likely cost me $1100 if you figure shipping. Comes with gear box and couplings to make your own PTO generator. It seems like the best deal because it is as cheap as the harbor freight item but most likely a better generator. 15kw st They also have a 10kw for $775.
So now I am trying to decide between #1 and #3. For how often I use it #1 sure sounds good if I can figure a cheap way to power it. If not I may go with #3.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Cautionary Tale - by Ian Minshull. In the early 1950s my father bought an Allis Chalmers B and I used it for all the row crop work with the mangolds and potatoes, rolling and the haymaking on our farm. The farm and the Allis were sold and I have spent a lifetime working on farms throughout the country. I promised myself that one day I would own an Allis. That time event
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
