Farmall & IHC Tractors Discussion Board |
Re: Were They Serious
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on October 30, 2003 at 16:10:49 from (216.208.58.108):
In Reply to: Were They Serious posted by Wide Open Throttle on October 30, 2003 at 05:32:47:
The 4100 should pull 8 bottoms just about anywhere. I had a 5x16 seni- mount plow that I bought for use behind my 1066. It turned out to be such a light load for 1066 that I pulled it with 656. I will grant you my soil was a sandy loam, however I always plowed 7to 8 inches deep. I have seen guys pulling 7 and 8 with 1066 and 1466. I have neighbor who pulls 10x18 with a Case that is same configuration as that 4100. I think he told me it was under 200 hp. Plows really only require about 10 to 15 hp per bottom. 40 years ago I remember a guy in our neighbourhood buying a new Cochshutt 570 diesel and a 5x16 trailer plow. He plowed some quite heavy hills with that old Cockshutt. When you get a tractor loaded to point where you can't pull the plow or disk more than 4 mph your wear and breakage will be far less and fields much smoother. These new high speed bottoms just become a more expensive way to farm, and less profit for you. When you sit in that tractor seat for 15 to 18 hours per day for weeks at a time or 44 hours in two days as I have done, that high speed hurts the human flesh more than the tractor and plow. I know some of you will say," Hugh If you were going faster it wouldn't take so long." Hogwash, I say this game is about making money not high speed. When you can drive a 70s full size Ford or Chevy sedan at 50 mph on your fields, on sod of course, the fields are smooth.
Follow Ups:
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|