Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Piston rod bearings on a Farmall A C113 engine


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by MACE on February 19, 2005 at 06:03:54 from (4.154.122.44):

In Reply to: Re: Piston rod bearings on a Farmall A C113 engine posted by El Toro on February 19, 2005 at 05:15:30:

Hal,

That thought did cross my mind about the crankshaft being ground down. When I got into the engine, I found the crankpins to be in very good shape as far as I could tell, they look as if it is new crankshaft. The measurements are the same on all crank pins. I measured in three locations on the outsides and in the middle and came up with the same measurement. I noticed that someone had been in the engine before me due to the blue cylicone sealant in the engine. When I got the tractor, the rods and pistons had been removed. Thank you for the advice so far and for the tip to look at the bearings themselves. The bearings did not look in bad shape at all. The pistons were removed due to wear and from what I could tell some scoring on one of the cylinder walls. I notices that a chunk, about 1/2 square inch, of one of the cylinders was missing and assume it was drained out with the oil as I have cleaned the entire engine and found no metal. Do you think that I may be able to take a plastiguage and measure my clearances? If they coinside with what the book says, then my bearings may be ok. I would rather put new ones in, but I may have trouble finding the ones that I need.

Thanks,

MACE


Follow Ups:




Post a Followup

:
:
Hide: Yes No
Hiding your address protects you from spam generators but allows you to receive email response notifications.

Subject: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Identifying Tractor Noises - by Curtis Von Fange. Listening To Your Tractor : Part 3 - In this series we are continuing to learn the fine art of listening to our tractor in hopes of keeping it running longer. One particularly important facet is to hear and identify the particular noises that our ... [Read Article]

Latest Ad: 1997 cub cadet 7275 compact utility tractor 4wd hydro trans cracked block 3500 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy