Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: What's better 1066 0r 4440


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Cliff Neubauer on December 15, 2004 at 16:09:10 from (69.18.16.144):

In Reply to: Re: What's better 1066 0r 4440 posted by G/MAN on December 15, 2004 at 13:34:10:

You need to check your numbers. The 5088 has the DT-438 engine that had over 35% torque rise from the factory, I don't think Deere touched that until the 7000 series came out. The Deere engine is a good one but without a cross flow head it doesn't have the performance that the IH has and cost alot more to work on. The IH transmission is much heavier built than either of the Deere's and the same basic tranmission is still used on the MX Magnums. The IH's used a wet clutch as well and they almost never need replaced. The IH transmission is much easier to shift and from an operator's standpoint the clutch on the IH puts the Deere to shame. I guess you've never been in an 88 series cab because the only controls not on the right hand console are the park lock lever and the throttle. At Nebraska tractor tests the 88 series cab was quieter than Deere's and I think it has better visibility. When it comes to hydraulic's I'm pretty sure the 40 series Deere's have around 20 gpm at 2,500 psi to the remote valves, the IH's have 27 gpm at 2,750 psi and try adjusting the flow rate from the cab on a Deere. Off the top of my head I don't recall the lift capacity on the 3pt of the 88 series but it was close to 10,000lbs and the drawbar's on the IH's are alot stronger (try putting a 750 bushel grain cart on a 4440). The standard IH front axle was weak but the high capacity front axle offered on the 88 series is much heavier than the Deere's, they have used the same front axle on 2wd tractor's clear up through the current MX Magnum tractor's and I've never heard of one breaking. I won't say that there have been less repairs made on IH tractor's than Deere's but keep in mind that JD still hasn't built as many tractor's as IH did and they've had 20 years to catch up. I'm not saying that the Deere's aren't good tractor's but you'd better have some real numbers to back it up if your going to tell me that IH never built anything that compares to them.


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tuning-Up Your Tractor: Plugs & Compression Testing - by Curtis Von Fange. The engine seems to run rough. In the exhaust you can hear an occasion 'poofing' sound like somethings not firing on all cylinders. Under loaded conditions the tractor seems to lack power and it belches black smoke out of the exhaust. For some reason it just doesn't want to start up without cranking and cranking the starter. All these conditions can be signals that your unit is in need of a tune up. Ok, so what is involved in a tune up? You say, swap plugs and file the points....now tha ... [Read Article]

Latest Ad: 1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy