Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Ford 9N,2N 8N Tractor Forum Archives by Subject
[Sort by Subject]    [Search]    [Main Forum]

[ Previous Page]   Page 990 of 1270    [ Next Page ]

SubjectPosted ByYear
That fluid is mild EP GEAR OILRob2004
That is a good example of the blocking.Rob2005
That tube is fine!Rob2004
That was Bob, he's the genius.Rob2005
The N 3-pt is category 1.Rob2004
The control should stay where you put it.Rob2004
The genny reg canRob2004
The replacement ends are beveled.Rob2004
The screens I've seen are attached.Rob2004
There's a trick to brg inserts.Rob2004
There's an off chance that....Rob2004
This here laptop don't have no mouse.Rob2005
Thread chaser/chase nutsRob2004
Tip o' the hat to BigGeorge for heads-upRob2005
Too much choke floods the carb and you get gasRob2005
Too much choke.Rob2004
Torque it to 70ft-lbsRob2004
Try Kern County Tractor PartsRob2004
Try a jumper around the ignitionRob2004
Try this againRob2005
Try this.Rob2004
Two years to a sticky float valve!Rob2004
Types 'mineral oil' meant 'mineral spirits'Rob2004
U da MAN!Rob2005
U da man!Rob2004
Use your stabilizer bars.Rob2004
Valve lapping, latest verseRob2003
Well that's good to know!Rob2004
Well then you should be buying the beer next time!Rob2005
Well you're right about the threads.Rob2004
What did you do?Rob2005
What happened? I have 10-days of posts on one pageRob2004
What is in your grease gun?Rob2005
What is that? Some kinda phancy imported joe.Rob2005
What's that governor doing anyway?Rob2004
What's working well to keep air in the front tiresRob2005
What?Rob2005
Where was the little lady whileRob2004
Window on your N? Cracked block repair...Rob2005
Wire won't tell you it's open.Rob2004
With the price of gas...Rob2005
Won't hurt to know something bout 6v.Rob2004
Worried about water after a storm?Rob2004
Would it do any good if....Rob2004
Ya' know, you don't need sway bars with limiter chRob2004
Yeah, that old junk planter...Rob2004
Yeah, time to look at the front axle.Rob2004
Yep.Rob2004
Yes, I know other vehicles usedRob2004
You bet...Rob2004
You can pull the pin (valve core) out of any tire.Rob2004
You did adjust the brakesRob2004
You fised a leaky cylinder so youRob2004
You got 'em swapped.Rob2004
You got a new cable for a Sherman!Rob2005
You got that one right.Rob2004
You make sense on the measurement.Rob2004
You need a back-up.Rob2004
You want a pillow block and bearing insert.Rob2004
You'll find it in a hardware store.Rob2004
You're going to like that pivot.Rob2004
You're the guy that...Rob2004
Zane is of few words this morning.Rob2005
air cleaner doorRob2004
always worked for meRob2004
bolt-on steel wheels (rare?)Rob2003
cant get my rebuilt motor startedRob2004
connecting rod side clearanceRob2004
distributor not installed before head on...which wRob2004
firing order...Rob2003
got the tractor runningRob2004
loading your own tiresRob2004
massey loader on 8n ( value ? )Rob2004
motor oil; detergent v non-detergentRob2005
no sparkRob2003
right at 2-1/2Rob2004
screw at the end of crank...helpRob2004
shifter boot on 9nRob2003
terraserver.comRob2004
tractor death in Kansas yesterday.Rob2005
tractor doesnt start part 2Rob2004
valve retaining clips...wont slip inRob2004
Ford/New Holland prices.Rob2003
Four or five starter problem posts on this one page!Rob2002
Front axle spacing/clearanceRob2002
Front end blade for NRob2001
Front end loader?Rob2003
Front oil sealRob2003
Gasket sealer for oil pickup tube?Rob2002
Gen and Voltage regulatorRob2003
Generator wire size #10. Big wire eh....Rob2003
GeneratorRob1999
Good advise! thanks!Rob2003
Gray Paint codes are incorrect!!Rob1999
Hand Crank DriveRob2002
Heading to Knoxville next weekRob2002
Heavy-duty v Med dutyRob2003
Hey Dell (neighbor) - machine shopRob2002
Hey Kim, the board is acting up.Rob2003
How can I change the Board's preferences?Rob2002


[ Previous Page]   Page 990 of 1270    [ Next Page ]


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga ... [Read Article]

Latest Ad: Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy