Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Ford 9N,2N 8N Tractor Forum Archives by Subject
[Sort by Subject]    [Search]    [Main Forum]

[ Previous Page]   Page 989 of 1270    [ Next Page ]

SubjectPosted ByYear
If you're using that 134D universal fluidRob2004
Is that good for any points?Rob2004
It always looks like the bushing is leakingRob2004
It comes with a brace.Rob2004
It died when you took off the jumper cables?Rob2005
It does take some to get used to that valve.Rob2004
It just changed the size?Rob2005
It just lays against the lift arm.Rob2004
It makes perfect sense. Always helps toRob2004
It matters some.Rob2004
It's likely you give it way too much choke.Rob2004
It's not suppose to be at 12 o'clock.Rob2004
JIM COX where is Tractor Tech?Rob2005
Jazzed up the pic some.Rob2004
Jim Cox is hard at work but says Hi! to everyone.Rob2005
Kim, the board is acting up.Rob2005
Kim, you got spammers on the board !!!Rob2005
Know what? Maybe you don't have toRob2004
Latest homemade tool; modified anyway.Rob2004
Leave the manifold on there.Rob2005
Link to investment newsetter postRob2005
Live HYD and PTORob2003
Loctite thread repairRob2004
Looks like it screwed up the font.Rob2005
Looks like this guy has one.Rob2005
Looks like you'll have some blockingRob2005
Lube the cable with graphite powder.Rob2005
Lug nut pain in the neckRob2004
M2C134D hyd fluid recommendationRob2004
MPC says 1/2.Rob2004
Master Parts Catalog?Rob2004
Maybe you have the idler wheel wrong.Rob2004
Mid-Kansas auction reportRob2004
Might be a lever in frontRob2004
Might be running way rich.Rob2004
Modern motor oilsRob2005
More I look at it, more it looks like it hasn'tRob2004
Most folks get plenty for the 8N Operator's manualRob2005
My '51 8N acted like that.Rob2005
My 8N has a valve installed in theRob2004
Mysterious.Rob2005
N Central Ks; $2.999/gal, up 20-centRob2005
N is stable side to side but can flip easily.Rob2005
N need a thermostat?Rob2004
Need to seal the hydraulic oil tube.Rob2004
New brushes usually an inch or more.Rob2004
New flywheel thicknessRob2004
New owner so replaced points, cap, condenser....Rob2005
No down pressure.Rob2004
No response, eh?Rob2004
Nope. Go for it.Rob2004
Not anyRob2004
Not likely he needs 12v. He was baiting Dell.Rob2004
Not sure what it is that went dead.Rob2004
OT Octane boosterRob2005
OT; You ol-timers will like this.Rob2004
OUCH!Rob2005
Oh man..I quit smoking rope along time ago.Rob2004
Oh man..you are doomed.Rob2004
Oh that is funny!Rob2004
Oh yeah...Rob2005
Oil filter.Rob2004
Ok, there's that 'fork retracting spring.'Rob2005
Ol' fella jumped started his tractor today.Rob2005
One other thing.Rob2004
OooWee! Belt length..archive blowsRob2005
Photos!Rob2005
Pinion bearing preloadRob2004
Polarize it Mike.Rob2004
Pretty tractor in a pretty picture!Rob2004
Pull that sucker off...Rob2004
Put the tranny in neutral too.Rob2004
Rear main upper and lower rope packingRob2004
Reoccurring mess, huh?Rob2004
Replaced chamber gasket on belly pump.Rob2004
Rick sounds rightRob2004
Roy, check your brakes.Rob2004
See there's the rub...Rob2004
Seems it was just a hiccup.Rob2005
Seems the Brits use this on the cars.Rob2005
Shocks? You got shocks?Rob2004
Size of the 8ne10306 dropping resistorRob2005
Slim to no chance 12v will cure either problemRob2004
Small engine/magneto anyone?Rob2005
So that's what that is!Rob2004
So what did you end up doing?Rob2004
Solvent and degreaserRob2005
Some farmer been wrenchin on itRob2004
Sounds like a mix up to me.Rob2004
Sounds like mine.Rob2005
Sounds like the battery shot craps.Rob2004
Split it....Rob2004
Sprayer works so well on the N I have to share.Rob2005
Starter gear won't retract.Rob2005
Stay safe out there.Rob2005
Stuck clutch and grinding gearsRob2004
Take a look at the wheel brgs.Rob2004
Take another look at the drawing.Rob2004
Takes some getting used to.Rob2004
That .855 is minimum. Can go no less.Rob2004


[ Previous Page]   Page 989 of 1270    [ Next Page ]


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga ... [Read Article]

Latest Ad: Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy